Home » Blog » Firearms » Tikka » Best Scope Mounts for the Tikka T3x: Optilock Rings, Rails and Scope Pairings

Best Scope Mounts for the Tikka T3x: Optilock Rings, Rails and Scope Pairings

best Tikka T3x scope mounts

The best Tikka T3x scope mounts for most hunting rifles are the factory Optilock rings, which are machined to mate with the integral receiver rails on the T3 and T3x. Match the ring to your scope’s tube, choose the lowest height that clears the front of the scope, and you are set. If your rifle came with a Picatinny rail, that is the other route. We carry the Optilock rings in our Tikka T3x accessories collection.

This guide covers how to choose rings, the four Optilock sets we list, which T3x models come with a rail, and scopes that match the rings by tube size. It is a mounting guide, not a range report. We have no range data, so we do not rank scopes by performance.

Optilock ring setScope tubeMount heightMax scope outer diameter
1-inch Extra Low1 in. (also 26 mm)28.5 mm51 to 59 mm
1-inch Low1 in. (also 26 mm)30.5 mm55 to 63 mm
1-inch Medium1 in. (also 26 mm)35.5 mm65 to 73 mm
30 mm Extra Low30 mm30.5 mm55 to 63 mm

The figures come from Sako’s Optilock chart. The larger diameter applies to standard-contour barrels, and the smaller one to heavy-barreled rifles. Sako’s chart lists taller and additional 30 mm heights too, but the four above are the sets we list.

How to Choose Scope Mounts for a Tikka T3x

Three decisions settle almost every mounting question.

  • Tube size. Rings are made for one tube diameter. The 1-inch Optilock rings take 1-inch and 26 mm tubes, and the 30 mm rings take 30 mm tubes. The tube is the main spec on a scope’s page, and a ring only works on its own tube size.
  • Ring height. The ring has to lift the front of the scope clear of the barrel. Compare the scope’s outer diameter at the front with the chart column above. Scope pages usually list the objective lens size, which is smaller than the outer diameter, so check the maker’s specifications.
  • Rings or rail. The T3x has integral receiver rails that the Optilock rings grip directly. A Picatinny rail is a separate base that attaches through screw holes in the receiver, and some T3x models come with one fitted.

If your scope has a large front end or your barrel is a heavy contour, go up a height. If the rings sit too low, the scope can touch the barrel. If you go too high, the scope sits farther from your cheek.

Best Tikka T3x Scope Mounts: Optilock Rings

Optilock rings are machined from solid steel and sold as a pair in a clamshell pack, with a hex key. A patented spherical fastening ring makes mounting easier, and a protective sleeve keeps the scope body from being scratched. The sets we list are blued steel. They fit the T3 and T3x integral dovetail, and we do not claim a fit on any other Tikka model.

Optilock 1-inch Extra Low rings

The 1-inch Extra Low rings are the lowest set for a 1-inch scope, with a 28.5 mm mount height. Choose them if your scope’s outer diameter falls within the 51 to 59 mm range on the chart.

Optilock 1-inch Low rings

The 1-inch Low rings raise the scope to 30.5 mm and allow an outer diameter of 55 to 63 mm. They are the next step if the front of your scope is too wide for Extra Low.

Optilock 1-inch Medium rings

The 1-inch Medium rings sit at 35.5 mm and allow 65 to 73 mm. They suit a scope with a wide front end or a heavy-contour barrel, where the smaller chart figure applies.

Optilock 30 mm Extra Low rings

The 30 mm Extra Low rings are the 30 mm set we list. They have a 30.5 mm mount height and allow 55 to 63 mm. Choose them when your scope has a 30 mm tube, which covers many variable-power hunting scopes.

Optilock Rings or a Picatinny Rail?

On a T3 or T3x without a fitted rail, Optilock rings are the simple choice. They are sized to Tikka’s integral rails, and Sako’s chart tells you the height that suits your scope. A Picatinny rail gives you a long flat mounting surface that takes any ring made for the standard, which helps if you want to slide the scope forward or back. If your rifle already has a rail, choose rings that clamp to that rail and match your scope tube. If it does not, the Optilock rings are the factory mount for the T3 and T3x.

Picatinny Rails for the Tikka T3x and T1x

The question is often phrased as the best Picatinny rail for a Tikka, and our honest answer is that we do not sell a Tikka rail. What we can say is which models come with one, so you may not need to buy one. These are the T3x models Tikka lists with a rail:

  • The T3x CTR and TAC A1 rifles have a Picatinny rail on the receiver.
  • The T3x Ace rifles have a 20 MOA Picatinny rail.
  • The T3x Roughtech Ranch and the Super Varmint have a Picatinny rail as standard. See Tikka Roughtech and Tikka T3x.

The Lite Roughtech is different: Tikka’s copy lists extra screw holes in the receiver for a Picatinny rail, so it is ready for one, but we do not list a rail for it. The Tikka T3x Lite is listed with a drilled-and-tapped receiver.

The T1x is a separate story. The T1x receiver has an integral dovetail and is drilled and tapped, and the T1x Ace Target has a 20 MOA Picatinny rail. Tikka does not state that T3x Optilock rings fit the T1x, so we do not recommend them for it. For the rimfire line, see our Tikka T1x review and the Tikka T1x collection.

Best Scope for a Tikka T3x

Any scope whose tube matches the ring will mount. For the 1-inch Optilock rings, that means a 1-inch scope, and for the 30 mm rings, a 30 mm scope. These are scopes we list with a stated tube size. Check each page for the outer diameter before you choose a ring height.

When you read a scope’s page, check four things:

  • Tube diameter: 1 inch or 30 mm decides which rings fit.
  • Outer diameter at the front: compare it with the chart before you pick a height.
  • Eye relief: a longer eye relief gives you more room to set the scope on a harder-recoiling cartridge.
  • Focal plane: a first-focal-plane reticle scales with magnification, and a second-focal-plane reticle stays the same size.

1-inch scopes for the Optilock 1-inch rings

The SIG Sauer Buckmasters 3-9×40 BDC is a 3-9x scope with a 40 mm objective and a ballistic reticle in the second focal plane. Its page lists a 1-inch tube, so it takes the 1-inch rings.

The SIG Sauer Buckmasters 3-12×44 BDC also has a 1-inch tube, for a hunter who wants more top-end magnification than a 3-9x.

30 mm scopes for the Optilock 30 mm rings

The SIG Sauer Whiskey4 3-12×44 has a 30 mm tube and a second-focal-plane BDC-1 reticle, with a 44 mm objective and no illumination.

The SIG Sauer Whiskey4 4-16×44 has a 30 mm tube and a first-focal-plane MOA Milling 2.0 reticle, for a shooter who wants more magnification. The SIG Sauer Sierra6 BDX 3-18×44 also has a 30 mm tube, with a BDX-R2 reticle.

Scopes for a Tikka T3x Lite in .308 Win

Take a T3x Lite in .308 Win, such as this blued rifle with a 20-inch threaded barrel. It has a synthetic stock and a drilled-and-tapped receiver. Either tube size works with the Optilock rings, so choose by the magnification range and reticle you want, then check the outer diameter against the height chart.

Scopes for the Tikka T1x

For a rimfire, choose a scope whose page names the cartridge. The Burris Droptine 3-9×40 Ballistic Plex 22LR names the .22 LR in its title. It does not give a tube size on its page, so confirm the tube before you buy rings.

Mounting Basics Before You Start

A few habits make any mounting job easier, whichever mount you choose. Make sure the rifle is unloaded and the bolt is out. Set the rings loosely on the rails, slide the scope to a comfortable eye relief with the rifle shouldered, and level the reticle with the rifle held steady. Then tighten the ring screws evenly, following the instructions in the ring pack, and confirm your zero at the range. Optilock rings come with a hex key, so you can do the work with the tool in the box.

If your scope sits too low or too high, change the ring height rather than forcing the fit. A swap to the next height takes a few minutes, and it protects the scope and the barrel.

Which Mount Should You Buy?

  • For a T3 or T3x with a 1-inch scope, start with the Optilock 1-inch rings in the lowest height that clears the scope.
  • For a T3 or T3x with a 30 mm scope, use the Optilock 30 mm rings.
  • For a T3x that already has a Picatinny rail, use rings that match your scope tube and clamp to the rail.
  • For a T1x, do not assume Optilock rings fit. Confirm the mount with Tikka first.

For the wider model map, see Tikka rifle models explained, and for what carries over from the older rifle, see Tikka T3 vs T3x.

Shop Tikka Scope Mounts and Optics

Browse the rings on Tikka T3x accessories, then pick a scope from our Scopes category. More rings and bases from other makers are in Optic Mounts and Rings. For the rifles themselves, start with the Tikka rifles page.

Related Comparisons

FAQ

What scope rings fit a Tikka T3x?

Tikka’s Optilock rings are machined to mate with the integral receiver rails on Sako and Tikka rifles, including the T3 and T3x dovetail. We list 1-inch and 30 mm sets in the Tikka T3x accessories collection.

What height Optilock rings do I need?

Choose by your scope’s outer diameter at the front. The chart gives 51 to 59 mm for 1-inch Extra Low, 55 to 63 mm for 1-inch Low, 65 to 73 mm for 1-inch Medium, and 55 to 63 mm for 30 mm Extra Low.

Does the Tikka T3x come with a Picatinny rail?

Some models do, including the CTR, TAC A1, Ace, Roughtech Ranch, and Super Varmint. Others, such as the T3x Lite, have a drilled-and-tapped receiver and the integral rails that Optilock rings use.

What is the best scope for a Tikka T3x Lite in .308 Win?

Any scope with a tube that matches your rings will mount. We list 1-inch and 30 mm scopes, and both tube sizes have Optilock rings. Check the scope’s outer diameter against the ring height chart.

Do Optilock rings fit the Tikka T1x?

We do not claim that they do. Tikka does not state a T1x fit for Optilock rings, so confirm with Tikka before you buy rings for a T1x.

Comments

Leave a Reply

Your email address will not be published. Required fields are marked *