Home » Blog » Optics » EOTECH » EOTECH Riser Guide: Heights, Co-Witness, and Magnifier Setups

EOTECH Riser Guide: Heights, Co-Witness, and Magnifier Setups

best EOTECH riser

The best EOTECH riser is the one built for your sight’s co-witness height. For lower 1/3 co-witness sights such as the EXPS3 and EXPS2, that’s the FAST Optic Riser from Unity Tactical. For the XPS2 and XPS3, which Unity describes as absolute co-witness sights, it’s the FAST Absolute Riser, and Unity’s compatibility tool pairs that riser with the 512 as well.

Either riser puts the sight’s optical centerline 2.26 inches above the rail. If you plan to add a magnifier, Unity’s FAST FTC OMNI holds a G33, G43, or G45 at that same height, so the magnifier stays in line with the raised sight. The table below shows the match for each sight.

SightUnity FAST riserWhy it matches
EOTECH EXPS3FAST Optic RiserLower 1/3 co-witness; named in Unity’s tool
EOTECH EXPS2FAST Optic RiserLower 1/3 co-witness; part of the EXPS series
EOTECH XPS2FAST Absolute RiserAbsolute co-witness; named in Unity’s tool
EOTECH XPS3FAST Absolute RiserAbsolute co-witness; part of the XPS series
EOTECH 512FAST Absolute RiserNamed in Unity’s tool
EOTECH 552None namedNot in Unity’s tool

Why Put an EOTECH on a Riser?

Every EOTECH sight in this guide mounts straight to a 1-inch Weaver or MIL-STD-1913 rail, so a riser is optional. What it adds is height. Unity says a 2.26-inch optical centerline promotes a heads-up posture and faster reticle acquisition, even when you wear a communications headset, night-vision goggles, or a protective mask. If you shoot with a more upright head position, a riser brings the sight up to your eye, so you don’t have to drop your cheek to the stock.

A riser isn’t for everyone, though. If you shoot from a traditional cheek weld, or you want your iron sights to co-witness as EOTECH intended, mount the sight directly to the rail.

There is also a trade-off up close. At very short distances, your shots land below your point of aim, and a taller mount widens that gap, so confirm your holds at the distances you actually shoot.

EOTECH Co-Witness and Riser Height

Co-witness describes where your iron sights appear in the EOTECH window. EOTECH says sights with side buttons or a factory quick-detach lever co-witness in the lower 1/3 of the window, while all other models co-witness in the center, which is absolute co-witness. The EXPS3 and EXPS2 have both features, and the EXPS3 sits on a 7mm raised quick-detach base for lower 1/3 co-witness. EOTECH’s cross-bolt mounts, by contrast, offer absolute co-witness height.

That difference in starting height is why Unity makes two risers. Each one brings its type of sight to the same 2.26-inch centerline, so the riser built for lower-sitting absolute sights is the taller part, as the table below shows. Put an EXPS on the Absolute Riser or an XPS on the Optic Riser, and the sight ends up above or below 2.26 inches, out of line with a FAST magnifier mount.

Unity FAST partOptical centerlinePart heightWeight
FAST Optic Riser2.26 inUnder 0.8 inUnder 3.0 oz
FAST Absolute Riser2.26 inUnder 1.0 inUnder 3.5 oz
FAST FTC OMNI2.26 inUnder 3.5 in raised; under 2.2 in stowedUnder 4.5 oz

These are Unity’s figures, with the optical centerline measured from the rail. One caution: EOTECH’s co-witness guidance is written for the standard AR-15 platform, and a riser lifts the sight above the height that guidance assumes. Check how your iron sights line up once the sight is mounted.

How to Pick the Best EOTECH Riser

Start with the sight you own or plan to buy, then match the riser to its co-witness height. Our EOTECH risers collection carries both Unity risers and the OMNI magnifier mount.

  • FAST Optic Riser: Unity builds it for most lower 1/3 co-witness rail-mounted sights, such as the EOTECH EXPS series, and its compatibility tool names the EXPS3. Choose it for an EXPS3 or EXPS2.
  • FAST Absolute Riser: Unity builds it for most absolute co-witness rail-mounted sights, such as the EOTECH XPS series, and its tool names the XPS2 and 512. Choose it for an XPS2, XPS3, or 512.

Both risers attach to a MIL-STD-1913 rail with an included rail clamp and two cross bolts, and both accept Unity’s FAST QD Lever, sold separately, if you want a quick-detach mount. Your EOTECH mounts on top with the hardware that came with the sight. Unity’s instructions call for a T25 bit and 35 in-lbs (4 Nm) on the clamp screws, and they advise against thread-locking compound.

Lining Up a Magnifier Behind a Raised EOTECH

Running a riser with a magnifier means raising both, because a magnifier has to sit on the same optical centerline as the sight in front of it. Unity says both risers pair with any FAST FTC magnifier mount, and for EOTECH magnifiers, it points to the FAST FTC OMNI. The OMNI holds a G33, G43, or G45 at the same 2.26 inches.

The OMNI takes the place of EOTECH’s own magnifier mount, so buy the magnifier in its no-mount version: the EOTECH G33 or EOTECH G43 at 3x, or the EOTECH G45 at 5x. Our EOTECH G33 vs G43 vs G45 guide compares them.

EOTECH’s STS (switch-to-side) mount moves the magnifier to the side when you don’t need it. The OMNI flips it down instead. Unity’s flip-to-center design stows the magnifier below the optical sight plane and within the footprint of the receiver, and the mount has an integrated FAST QD lever. Unity notes that some optic combinations may slightly block the sight picture when the magnifier is stowed, though most will not.

To line up a magnifier behind a raised sight:

  1. Mount the riser and sight, then confirm your zero.
  2. Seat the no-mount magnifier in the OMNI’s arm with Unity’s screws, without the shims from an OEM magnifier kit, and torque the screws to EOTECH’s specification for your magnifier.
  3. Clamp the OMNI to the rail behind the sight and set the distance so you see a full, clear image from your normal head position. Eye relief is 2.2 inches on the G33, 2.5 inches on the G43, and 2.6 inches on the G45.
  4. Use the magnifier’s tool-free vertical and horizontal adjustments to center the magnified image behind the sight.

The EOTECH 512 and 552 on a Riser

Unity’s compatibility tool pairs the EOTECH 512 with the FAST Absolute Riser, so that’s the riser for a 512 build. The 512 runs on two AA batteries, measures 5.6 inches long, and attaches with a knobbed, tool-less mounting bolt. It has no night-vision settings.

The EOTECH 552 is a different case. It’s a night-vision-compatible AA model, with 10 additional settings for Gen I through III+ devices, and EOTECH lists it with back buttons and a cross-bolt mount. Unity doesn’t list the 552, so we don’t claim a riser fit for it. Confirm with Unity before you order one.

Button placement also matters once you add a magnifier. EOTECH says side buttons are ideal for adjustments with an EOTECH magnifier mounted behind the sight, while back buttons let you adjust without taking your eyes off the target. If you’re buying a sight for a magnified riser setup, that points to the side-button EXPS3 or EXPS2. Our EOTECH 512 vs 518 comparison covers the AA models in more detail.

Which Should You Buy?

Start from the sight, and the riser choice follows:

  • EXPS3 or EXPS2: the FAST Optic Riser. The EXPS3 adds night-vision settings, which the EXPS2 lacks.
  • XPS2 or XPS3: the FAST Absolute Riser. The XPS3 is the night-vision-compatible one.
  • 512: the FAST Absolute Riser.
  • 552: no riser named by Unity, so check with Unity first.
  • Adding a magnifier: the FAST FTC OMNI with a no-mount G33, G43, or G45, behind the matching riser.

Building from scratch? An EXPS3 on a FAST Optic Riser, with an OMNI and a no-mount magnifier behind it, uses only pairings Unity confirms. It also gives you the side buttons EOTECH calls ideal with a magnifier. If you’re still choosing a sight, our guide to EOTECH models walks through the full lineup.

Shoppers also search for EOTECH risers from LaRue, ADM, Wilcox, GBRS, and Scalarworks; this guide sticks to Unity’s FAST line because that’s what we carry.

Shop EOTECH Risers, Sights, and Magnifiers

Pick the riser that matches your sight, then add a magnifier if you want one. Browse our EOTECH holographic sights for the sight itself, or see everything we carry from EOTECH.

Related Comparisons

FAQ

What is the best EOTECH riser?

The best EOTECH riser is the one matched to your sight’s co-witness height. Unity’s FAST Optic Riser is built for lower 1/3 sights such as the EXPS series, and the FAST Absolute Riser for absolute sights such as the XPS series and, per Unity’s compatibility tool, the 512.

Which riser fits the EOTECH 512?

Unity’s FAST compatibility tool pairs the EOTECH 512 with the FAST Absolute Riser. That riser is built to put the sight’s optical centerline 2.26 inches above the rail.

How high does a Unity FAST riser put an EOTECH?

Unity’s FAST Optic Riser and FAST Absolute Riser each create a 2.26-inch optical centerline from the rail when paired with the type of sight they are built for. Unity’s FAST FTC OMNI holds a magnifier at the same height.

Can you use an EOTECH magnifier with a riser?

Yes, as long as the magnifier is raised to match. Unity’s FAST FTC OMNI holds a G33, G43, or G45 at the same 2.26-inch centerline as its risers, and Unity says both risers pair with any FAST FTC magnifier mount.

Will an EOTECH on a riser still co-witness with iron sights?

EOTECH’s co-witness guidance is written for the standard AR-15 platform: lower 1/3 for models with side buttons or a factory quick-detach lever, and the center of the window for all others. A riser lifts the sight above that height, so check your iron sight alignment after mounting.

What is the EOTECH STS mount?

The STS (switch-to-side) mount is the EOTECH magnifier mount that moves the magnifier to the side when you don’t need it. Unity’s FAST FTC OMNI flips the magnifier down instead and holds it at a 2.26-inch centerline to match a raised sight.

Do Unity risers have a quick-detach lever?

Not out of the box. Both FAST risers ship with a rail clamp and two cross bolts and accept Unity’s FAST QD Lever, sold separately, while the FAST FTC OMNI has an integrated FAST QD lever.

Comments

Leave a Reply

Your email address will not be published. Required fields are marked *